HammondWiki - Diff: AddATenthSetOfContacts

Differences between version 7 and previous revision of AddATenthSetOfContacts.

Other diffs: Previous Major Revision, Previous Author

Newer page: version 7 Last edited on December 28, 2010 8:54 pm. by
Older page: version 6 Last edited on September 7, 2010 10:58 pm. by
@@ -26,29 +26,29 @@
  
  
 I am the anonymous editor who added the above comment. 
  
-I know little about this site and/or how to log in and/or enter a password . I tried but, to no avail
+I am Alan P . DuBois and I own and work with Hammonds
  
-I am Alan P . DuBois and I work with Hammonds. freshairband@limo.net  
+I am editing this post to reflect my latest discoveries regarding L & M100 manual chassis that will accomodate 10 busbars
  
-To add further to my above comment:  
+The L133 manual chassis I originally spoke of is of different design than any other Hammond chassis I have seen.  
+The actuators, contact boards and terminal strip are ALL made of plastic - Hammond chassis usually have bakelite boards, etc., - interesting....  
  
-I have worked with many M100-series manual chassis.  
 NONE of the *M100* chassis I have worked with will accomodate 10 busbar contacts. 
+That is, _until recently!_  
  
-I have also worked with many L100 manual chassis .  
-The ONLY L100 manual chassis I have found that will accept 10 drawbar contacts is the L133. 
+I opened both an M103 and an L111 recently and they _both_ have room for a tenth busbar _and_ room for contacts for the tenth busbar, if installed . These chassis are the same as the L133 I described above. All plastic guts
  
-This particular L133 manual chassis I speak of is of different design than any other Hammond chassis I have seen .  
- The actuators , contact boards and terminal strip are ALL made of plastic - Hammond chassis usually have bakelite boards , etc. , - interesting...
+I checked my history working with these spinets and found that 1964 and earlier used the bakelite boards and would not accomodate 10 busbars. I have _not_ been into a 1965 vintage spinet . The last two models I opened up are 1966 vintage.  
+  
+So , it was obviously a production change in 1966 (for sure) and possibly 1965, where Hammond added this "feature."  
+  
+To find out if your L or M100 has such a chassis, from frontside , remove the metal L -shaped cover from the lower manual chassis assembly (two screws at each end)
  
-I added foldback to this particular chassis and I sold it - so I cannot give any more particulars about this "unique" chassis. I do have a photo of the backside of this L133 chassis but I have no idea how to post it here
+If the terminal contacts are mounted to a black, plastic board (as shown below), chances are you have one of these 10-busbar chassis. 
  
-I can only agree with the original post in that the ACTUATORS for M, L100s DO have 10 slots .  
-BUT, regarding adding a tenth contact, not all the L, and /or M100 chassis have slots for 10 contacts!  
+[http://comics .limo.net /L100CHASSIS/BOTTOM.JPG]  
  
-All I can say is, beware of buying an M-, or L-100 with hopes of adding a 10th set of contacts and/or a 10th busbar.  
-You should find out what's inside the chassis before you buy!  
  
  
 Thanx, Alan 

The content of this page is Copyright (C) 2000, 2001, 2002 Geoffrey T. Dairiki and the other authors of the content, whoever they may be.
This is free information and you are welcome redistribute it under certain conditions; see http://www.dairiki.org/HammondWiki/opl.html for details.
Absolutely no warrantee is made as to the correctness of the information on this page.