Differences between current version and predecessor to the previous major change of CapacitorReplacement.

Other diffs: Previous Revision, Previous Author

Newer page: version 30 Last edited on February 22, 2011 8:11 am. by JeffDairiki
Older page: version 28 Last edited on October 8, 2010 10:14 am. by JeffDairiki
@@ -1,5 +1,5 @@
-The electrolytic capacitors in old (and new) electronic equipment use a wet dielectric --- they dry out with age. This happen whether in use, or sitting on a shelf in a warehouse --- in fact, use may prolong their life, see [CapacitorReforming]). They have a shelf-life, usually stated to be on the order of ten to twenty years. 
+The electrolytic capacitors in old (and new) electronic equipment use a wet dielectric --- they dry out with age. This happens whether in use, or sitting on a shelf in a warehouse --- in fact, use may prolong their life, see [CapacitorReforming]). They have a shelf-life, usually stated to be on the order of ten to twenty years. 
  
 The ''wax-and-paper'' caps also "dry out" and have a similar lifetime. 
  
 As ToneWheel Hammonds ([Leslie]s too) are in general, twenty-nine to sixty-eight years old, their caps are long since past their "pull date". Eventually, old caps will cause problems. Possible symptoms range from hum to tonal degradation to explosion and fire. Many feel that the capacitors should be replaced as a matter of course ([PreventativeMaintenance].) 
@@ -19,21 +19,21 @@
  
 ------ 
 ! Mounting Replacement Capacitors 
  
-Most often, many of the electrolytic capacitors needing replacement are of the multi-section can type. These caps usually plug into sockets, and protrude from the top of your (pre-)amp chassis --- each aluminum can actually contains several (two to four) separate capacitors. These capacitors are no longer manufactured (well, there are some manufactured in Mexico, but their quality is highly suspect), so generally one needs to replace them with individual capacitors. 
+Most often, many of the electrolytic capacitors needing replacement are of the multi-section can type. These caps usually plug into sockets, and protrude from the top of your (pre-)amp chassis --- each unit can actually contain several (two to four) separate capacitors. These capacitors are no longer manufactured (well, there are some manufactured in Mexico, but their quality is highly suspect), so generally one needs to replace them with individual capacitors. 
  
 (Another alternative is provided by ZackEngineering, who makes replacement multi-section capacitors from modern miniturized electrolytics.) (Yet another alternative is FrontierCapacitor, who, reportedly, will "rebuild" your multi-section can caps for you --- removing the old guts and replacing them with modern caps.) 
 (And yet another place which seems to be custom-building multi-section caps: [askjanfirst.de|http://www.askjanfirst.de/eindex.htm].) 
  
 How then to mount the replacement capacitors? Here's what I do: 
  
 * Unsolder all the connections from the old can caps, but leave them in place. Otherwise you'll have holes in the chassis which you'll want to cover or plug. 
-* Get two terminal strips an pop-rivet them to the inside of the chassis. They should be spaced a little farther apart than the length of your replacement ''axial-lead'' capacitors. 
+* Get two terminal strips and pop-rivet them to the inside of the chassis. They should be spaced a little farther apart than the length of your replacement ''axial-lead'' capacitors. 
 * The replacement caps mount between the two terminal strips, one lead to each terminal strip. (Use hookup wire, if needed, to make the connection from the terminal strip to wherever the capacitor is needed.) 
 ~JeffDairiki 
  
-Here are some pictures of caps that have been replaced on a T-582c spinet organ. As you can see, the owner (myself) was lazy and did not bother with terminal strips. I just twisted + soldered the caps onto the wires. To make it easier, since oftentimes there were several wires to the positive lead, I simply used a pair of needlenose pliers and tore the metal terminal-piece they were soldered to off of the old cap, and soldered the lead onto that. I covered up the leads and connections with electrical tape to avoid shorts and other nasty things that can happen to the unwitting. I recommend you do a good solder job to save the trouble later. Remember, with the kind of power running through there, any resistance is just going to get hotter and hotter and eventually your connections will fail.. Whoops, there goes your organ. 
+Here are some pictures of caps that have been replaced on a T-582c spinet organ. As you can see, the owner (myself) was lazy and did not bother with terminal strips. I just twisted and soldered the caps onto the wires. To make it easier, since oftentimes there were several wires to the positive lead, I simply used a pair of needle-nose pliers and tore the metal terminal-piece they were soldered to off of the old cap, and soldered the lead onto that. I covered up the leads and connections with electrical tape to avoid shorts and other nasty things that can happen to the unwitting. I recommend you do a good solder job to save trouble later. Remember, with the kind of power running through there, any resistance is just going to get hotter and hotter and eventually your connections will fail. .. Whoops, there goes your organ. 
  
 [http://www.dairiki.org/hammond/pics/CapacitorReplacement/Cap_Replace_Underchassis.jpg] 
  
 The replaced caps have circles over them. I only ripped out one of the old caps, then I realised it was better to just leave them in and I disconnected the others and put electrical tape over the terminals. The two caps next to each other are replacing a canister-cap with two values. I tied the grounds together (Yeah, 18 gauge speaker wire happened to be sitting on the workbench and I didn't feel like hunting for anything better.) 
@@ -42,17 +42,17 @@
  
 There, it's as good as new. Except for that rather ugly hole where I ripped one out, you could never tell the caps were replaced. Note that these capacitors are attached to their cardboard-esque bases and riveted into the chassis, so they're a pain to remove, should you ever want to. 
 ~[PeterCsere] 
  
-Appropriate terminal strips are a bit tough to find, as they more-or-less are only used in tube equipment. In any case they come in various sizes (with varying numbers of terminals). Pick the ones that best fit the size and number of capacitors you have to mount (and fit in the space you have to mount them in.) 
+Appropriate terminal strips are a bit tough to find, as more-or-less they are only used in tube equipment. In any case they come in various sizes (with varying numbers of terminals). Pick the ones that best fit the size and number of capacitors you have to mount (and fit in the space you have to mount them in.) 
  
 MouserElectronics stocks some terminal strips which will do the job (though they are not my favorite style). The Mouser part numbers are 158-1002 through 158-1008 --- they are listed on page 202 of the current catalog (#605) (p. 180 in catalog #604). Here's a link to Mouser's [spec sheets|http://www.mouser.com/catalog/specsheets/KC-300255.pdf] for these terminal strips. 
  
 --JeffDairiki 
  
 If you replace a can cap with under-the-hood discrete caps, it would be a good idea, either to remove the cap socket altogether (and plug the resulting hole), or to otherwise disable the cap socket (ThomDay suggests potting with epoxy), to prevent the unsuspecting from plugging another cap (or their fingers). 
  
-Multi section can capacitors in correct values for the many Hammonds and Leslies, including the B3 and 122 style Leslies are available from http://www.tubesandmore.com Good quality made in USA on Malory's old equipment to the same specs. I have used them in several organs and leslies with good results 
+Multi section can capacitors in correct values for the many Hammonds and Leslies, including the B3 and 122 style Leslies are available from http://www.tubesandmore.com Good quality made in USA on Malory's old equipment to the same specs. I have used them in several organs and Leslies with good results 
  
 --Jon Peters 
  
 I've written an article detailing the replacement of the can capacitors (and the other electrolytics) in the AO-29 amplifier used in Hammond's M-100 series of spinet organs: [Overhauling the AO-29 Amplifier in the Hammond M-100 Series|http://www.stefanv.com/hammond_ao29_overhaul.html]. 

The content of this page is Copyright (C) 2000, 2001, 2002 Geoffrey T. Dairiki and the other authors of the content, whoever they may be.
This is free information and you are welcome redistribute it under certain conditions; see http://www.dairiki.org/HammondWiki/opl.html for details.
Absolutely no warrantee is made as to the correctness of the information on this page.